
Fasteners · 01 of 07
Stainless steel bolts
Hexagon, flange, mushroom head and eye bolts in SS 202, 304 and 316, from M3 to M48, to DIN, ISO and BS patterns.
- Laser cutting
- CNC bending
- Welding
- Finishing
Identify your fastener







Overview
Bolts: what and where
Hexagon bolts carry most structural and machine joints. Full-thread (DIN 933) suits short grips and general fixing; part-thread (DIN 931) gives a plain shank for shear loads.
- Standards
- 7
- Size range
- M3 – M48
- Usual grades
- SS 304 / SS 316
Used in
- Machine frames
- Electrical panels
- Conveyors
- Food equipment
- Pump & valve flanges
- Structural brackets
Types
7 types, one family
Hexagon, flange, mushroom-head and lifting eye bolts. Each type below is manufactured to the standard shown, in the grades listed further down.
- 01
DIN 933 / ISO 4017
Hex bolt, full thread
Thread runs right up to the head, so one bolt covers many grip lengths.
Used forMachine frames, brackets, general fixing
- 02
DIN 931 / ISO 4014
Hex bolt, part thread
A plain shank under the head takes shear load across the joint.
Used forHinged joints, structural connections
- 03
BS 1083
Hex head bolt, inch
Imperial hexagon bolt with BSW or UNC thread for older equipment.
Used forReplacement on imported machinery
- 04
DIN 6921
Hex flange bolt
Built-in flange spreads the load, so no separate washer is needed.
Used forSheet metal panels, automotive parts
- 05
DIN 603
Mushroom head square neck bolt
Smooth domed head with a square neck that locks in a square hole.
Used forWooden frames, guards, conveyor slats
- 06
DIN 580
Lifting eye bolt
Forged collar eye for vertical lifting of machines and covers.
Used forMotor and enclosure lifting points
- 07
DIN 444
Eye bolt
Eye end with a threaded shank, used as a pivot or anchor point.
Used forTie rods, hinges, tensioning
Technical data
Standards, sizes and dimensions
| Standard | Description | Size range |
|---|---|---|
| DIN 933 / ISO 4017 | Hexagon bolts, full thread | M3 – M48 |
| DIN 931 / ISO 4014 | Hexagon bolts, part thread | M3 – M48 |
| BS 1083 | Hexagon head bolts | 1/4" – 2" |
| DIN 6921 | Hexagon flange bolts | M5 – M20 |
| DIN 603 | Mushroom head square neck bolts | M5 – M20 |
| DIN 580 | Lifting eye bolts | M6 – M36 |
| DIN 444 | Eye bolts | M5 – M39 |
| Size | Pitch (mm) | Across flats ISO (mm) | Across flats DIN (mm) | Head height k (mm) |
|---|---|---|---|---|
| M3 | 0.5 | 5.5 | 5.5 | 2.0 |
| M4 | 0.7 | 7 | 7 | 2.8 |
| M5 | 0.8 | 8 | 8 | 3.5 |
| M6 | 1.0 | 10 | 10 | 4.0 |
| M8 | 1.25 | 13 | 13 | 5.3 |
| M10 | 1.5 | 16 | 17 | 6.4 |
| M12 | 1.75 | 18 | 19 | 7.5 |
| M14 | 2.0 | 21 | 22 | 8.8 |
| M16 | 2.0 | 24 | 24 | 10.0 |
| M20 | 2.5 | 30 | 30 | 12.5 |
| M24 | 3.0 | 36 | 36 | 15.0 |
| M30 | 3.5 | 46 | 46 | 18.7 |
| M36 | 4.0 | 55 | 55 | 22.5 |
Nominal values from the standard. Lengths follow the standard series; non-standard lengths on request.
| Thread | ISO metric coarse; fine and BSW on request |
|---|---|
| Head | Hexagon, flange, mushroom, eye |
| Property class | A2-70 / A4-70 typical; A4-80 on request |
| Finish | Plain stainless |
| Stainless steel grades | 202 · 304 · 310 · 316 · 316L · 410 |
| Other materials | HT · MS · Copper · Brass · Titanium |
Usually manufactured in:
- SS 304 (A2)
- SS 316 / 316L (A4)
- SS 202
| Grade | Designation | Magnetic | Density | Max service temp. | Best for |
|---|---|---|---|---|---|
| SS 202 | Cr-Mn austenitic | Slightly | 7.80 g/cm³ | ≈ 800 °C | Indoor and dry conditions; lowest cost stainless |
| SS 304 (A2) | EN 1.4301 | No (annealed) | 8.00 g/cm³ | ≈ 870 °C | General-purpose; most common stainless fastener |
| SS 316 / 316L (A4) | EN 1.4401 / 1.4404 | No (annealed) | 8.00 g/cm³ | ≈ 870 °C | Marine, chemical and food environments |
Choosing
Picking the right one
Quick guidance from the standards. For critical joints, follow your design calculation.
Full thread or part thread?
Use full thread (DIN 933) for short grips and general fixing. Use part thread (DIN 931) when the joint carries shear, so the plain shank, not the thread, sits in the shear plane.
Which length?
The bolt should pass through the nut by at least one to two thread pitches. Measure length from under the head to the tip.
ISO or DIN head size?
From M10 to M22 some ISO heads are one size smaller across flats than DIN. Check your spanner size in the dimension table.
Size finder
Pick a size. See the numbers.
Thread pitch, spanner size, head and nut heights, Allen key and washer dimensions for ISO metric coarse fasteners.
- Pitch
- mm, coarse
- Spanner (ISO)
- mm across flats
- Spanner (DIN)
- mm across flats
- Bolt head height
- mm, ISO 4017
- Nut height
- mm, ISO 4032
- Allen key
- mm, ISO 4762
- Plain washer
- d1 × d2 × s, DIN 125A
- Spring washer
- d2 × s, DIN 127B
Quick quote
Quote for bolts
Tell us the standard, size, length, grade and quantity. We confirm manufacturing lead time and price.
- Reply with a quotation for prototypes or batches
- Reference number by email as soon as you send
- Or call Daksh Shah on +91 90823 86814
Quote checklist
Tap what you already have
- Cut3 kW fibre laser
- Bend100 t, 3200 mm
- WeldLaser · TIG · arc
- FinishGrind · polish
Have a drawing ready? Send it for a quote.
Share the drawing, material, quantity, finish and delivery date. We review it and reply with a quotation for prototypes or repeat batches.