
Fasteners · 06 of 07
Stainless steel washers
Plain, spring, toothed and taper washers in SS 304 and 316 that spread load, help resist loosening and seat bolts square.
- Laser cutting
- CNC bending
- Welding
- Finishing
Identify your fastener






Overview
Washers: what and where
Washers spread load under the head or nut. Spring and toothed washers help resist loosening, and taper washers sit square on channel and beam flanges.
- Standards
- 5
- Size range
- M4 – M27
- Usual grades
- SS 304 / SS 316
Used in
- Every bolted joint
- Earthing & bonding
- Structural steel
- Panels & covers
- Food equipment
- Outdoor fixtures
Types
5 types, one family
Plain, spring, lock and taper washers. Each type below is manufactured to the standard shown, in the grades listed further down.
- 01
DIN 125A
Plain washer
Flat washer that spreads the clamp load and protects the surface.
Used forUnder almost every bolt head and nut
- 02
DIN 127 / IS 3063
Spring washer, flat section
Split helical washer that keeps some tension in the joint.
Used forGeneral machinery, electrical
- 03
IS 6735
Spring washer, square section
Heavier square-section spring washer.
Used forHeavier joints, structural
- 04
DIN 6797 / 6798
Toothed and serrated lock washers
Teeth bite into the surface; also improve earth contact.
Used forEarthing points, electrical panels
- 05
DIN 434 / 435
Square taper washer
Wedge washer so bolts sit square on sloped flanges.
Used forChannel (434) and I-beam (435) flanges
Technical data
Standards, sizes and dimensions
| Standard | Description | Size range |
|---|---|---|
| DIN 125A | Plain washers | On request |
| DIN 127 / IS 3063 | Spring washers, flat section | On request |
| IS 6735 | Spring washers, square section | On request |
| DIN 6797 / 6798 | Toothed and serrated lock washers | On request |
| DIN 434 / 435 | Square taper washers for channels and I-sections | M8 – M27 |
| Size | Plain d1 (mm) | Plain d2 (mm) | Plain s (mm) | Spring d1 (mm) | Spring d2 (mm) | Spring s (mm) |
|---|---|---|---|---|---|---|
| M4 | 4.3 | 9 | 0.8 | 4.1 | 7.6 | 0.9 |
| M5 | 5.3 | 10 | 1.0 | 5.1 | 9.2 | 1.2 |
| M6 | 6.4 | 12 | 1.6 | 6.1 | 11.8 | 1.6 |
| M8 | 8.4 | 16 | 1.6 | 8.2 | 14.8 | 2.0 |
| M10 | 10.5 | 20 | 2.0 | 10.2 | 18.1 | 2.2 |
| M12 | 13 | 24 | 2.5 | 12.2 | 21.1 | 2.5 |
| M16 | 17 | 30 | 3.0 | 16.2 | 27.4 | 3.5 |
| M20 | 21 | 37 | 3.0 | 20.2 | 33.6 | 4.0 |
| M24 | 25 | 44 | 4.0 | 24.5 | 40.0 | 5.0 |
Nominal values from the standard. Lengths follow the standard series; non-standard lengths on request.
| Types | Plain, spring, toothed, taper |
|---|---|
| Standards | DIN 125A, DIN 127, IS 3063, IS 6735, DIN 6797/6798, DIN 434/435 |
| Grade | SS 304 / 316 |
| Finish | Plain |
| Stainless steel grades | 202 · 304 · 310 · 316 · 316L · 410 |
| Other materials | HT · MS · Copper · Brass · Titanium |
Usually manufactured in:
- SS 304 (A2)
- SS 316 / 316L (A4)
| Grade | Designation | Magnetic | Density | Max service temp. | Best for |
|---|---|---|---|---|---|
| SS 304 (A2) | EN 1.4301 | No (annealed) | 8.00 g/cm³ | ≈ 870 °C | General-purpose; most common stainless fastener |
| SS 316 / 316L (A4) | EN 1.4401 / 1.4404 | No (annealed) | 8.00 g/cm³ | ≈ 870 °C | Marine, chemical and food environments |
Choosing
Picking the right one
Quick guidance from the standards. For critical joints, follow your design calculation.
Plain washer size
Match the inner diameter to the bolt: an M10 bolt takes a 10.5 mm hole washer. The outer diameter spreads the load on soft or slotted parts.
Spring or toothed?
Toothed washers help earth continuity on painted panels. On critical vibrating joints, a nylock nut or correct preload is more reliable than a spring washer.
Taper washers
Use DIN 434 on U-channel flanges (8 % slope) and DIN 435 on I-beam flanges (14 % slope).
Size finder
Pick a size. See the numbers.
Thread pitch, spanner size, head and nut heights, Allen key and washer dimensions for ISO metric coarse fasteners.
- Pitch
- mm, coarse
- Spanner (ISO)
- mm across flats
- Spanner (DIN)
- mm across flats
- Bolt head height
- mm, ISO 4017
- Nut height
- mm, ISO 4032
- Allen key
- mm, ISO 4762
- Plain washer
- d1 × d2 × s, DIN 125A
- Spring washer
- d2 × s, DIN 127B
Quick quote
Quote for washers
Tell us the standard, size, length, grade and quantity. We confirm manufacturing lead time and price.
- Reply with a quotation for prototypes or batches
- Reference number by email as soon as you send
- Or call Daksh Shah on +91 90823 86814
Quote checklist
Tap what you already have
- Cut3 kW fibre laser
- Bend100 t, 3200 mm
- WeldLaser · TIG · arc
- FinishGrind · polish
Have a drawing ready? Send it for a quote.
Share the drawing, material, quantity, finish and delivery date. We review it and reply with a quotation for prototypes or repeat batches.