
Fastener manufacturer · since 1996
Stainless steel fasteners
We manufacture bolts, nuts, screws, studs and washers in SS 202, 304, 310 and 316 to DIN, ISO, IS and BS patterns. Pick a family for types, sizes and dimensions.
- Laser cutting
- CNC bending
- Welding
- Finishing
The range
Seven families. Made in-house.
Vinay Metal manufactures stainless steel fasteners in its own fastener production setup, to standard patterns or to your drawing. Order them on their own, or on the same purchase order as your sheet metal parts.
- Stainless steel grades
- 202 · 304 · 310 · 316 · 316L · 410
- Other materials
- HT · MS · Copper · Brass · Titanium
- Property class
- A2 / A4
- Standard finish
- Plain
- Standards
- DIN · ISO · IS · BS







Grade picker
Where will the fastener live?
Pick the environment. We suggest the grade most buyers use there, with its typical properties.
Recommended for indoor, dry
SS 202
Lowest-cost stainless. Fine for dry indoor furniture, fixtures and panels where moisture is low.
- SS 202
- DesignationCr-Mn austenitic
- MagneticSlightly
- Density7.80 g/cm³
- Max service temp.≈ 800 °C
Recommended for general & outdoor
SS 304 (A2)
The everyday stainless fastener. Good corrosion resistance for machines, panels and outdoor use away from salt.
- SS 304 (A2)
- DesignationEN 1.4301
- MagneticNo (annealed)
- Density8.00 g/cm³
- Max service temp.≈ 870 °C
Recommended for coastal, chemical, food
SS 316 / 316L (A4)
Molybdenum improves resistance to chlorides. Use near the coast, in chemical plants, pharma and food washdown.
- SS 316 / 316L (A4)
- DesignationEN 1.4401 / 1.4404
- MagneticNo (annealed)
- Density8.00 g/cm³
- Max service temp.≈ 870 °C
Recommended for high temperature
SS 310
High-chromium, high-nickel grade for ovens, furnaces and heat-treatment fixtures.
- SS 310
- DesignationEN 1.4845
- MagneticNo
- Density7.90 g/cm³
- Max service temp.≈ 1100 °C
Recommended for hard, self-tapping
SS 410
Martensitic and hardenable. Taps into steel sheet, but resists corrosion less than 304.
- SS 410
- DesignationEN 1.4006 (martensitic)
- MagneticYes
- Density7.75 g/cm³
- Max service temp.≈ 650 °C
Recommended for electrical contact
Brass / Copper
Good conductivity for terminals, earthing and bus connections.
- Brass
- DesignationCuZn37 / CuZn39Pb3
- MagneticNo
- Density8.4 – 8.5 g/cm³
- Max service temp.≈ 200 °C
- Copper
- DesignationCu-ETP
- MagneticNo
- Density8.94 g/cm³
- Max service temp.≈ 200 °C
Standards index
Find it by standard or name
41 of 41 standards
| Standard | Description | Size range | Family |
|---|---|---|---|
| DIN 933 / ISO 4017 | Hexagon bolts, full thread | M3 – M48 | Bolts |
| DIN 931 / ISO 4014 | Hexagon bolts, part thread | M3 – M48 | Bolts |
| BS 1083 | Hexagon head bolts | 1/4" – 2" | Bolts |
| DIN 6921 | Hexagon flange bolts | M5 – M20 | Bolts |
| DIN 603 | Mushroom head square neck bolts | M5 – M20 | Bolts |
| DIN 580 | Lifting eye bolts | M6 – M36 | Bolts |
| DIN 444 | Eye bolts | M5 – M39 | Bolts |
| DIN 934 / ISO 4032 | Hexagon nuts | On request | Nuts |
| BS 1083 | Hexagon nuts | 1/4" – 1.3/4" | Nuts |
| DIN 439 | Thin / jam / lock nuts | M3 – M48 | Nuts |
| DIN 982 / ISO 7040 | Nylock nuts | M5 – M24 | Nuts |
| DIN 985 | Nylock nuts, thin type | M3 – M20 | Nuts |
| DIN 1587 | Domed cap nuts | M4 – M24 | Nuts |
| DIN 315 | Wing nuts | M3 – M20 | Nuts |
| DIN 557 | Square nuts | M5 – M16 | Nuts |
| DIN 6923 | Hexagon flange nuts | M5 – M20 | Nuts |
| DIN 582 | Lifting eye nuts | M6 – M36 | Nuts |
| DIN 912 / ISO 4762 | Socket head cap (Allen) screws | M1.6 – M36 | Socket screws |
| BS 2470 | Socket head screws | 1/4" – 5/8" | Socket screws |
| DIN 7991 / ISO 10642 | Socket countersunk screws | M3 – M24 | Socket screws |
| ISO 7380 | Socket button head screws | M3 – M16 | Socket screws |
| DIN 916 / 913 / 914 / 915 | Set (grub) screws: cup, flat, cone and dog point | M3 – M20 | Socket screws |
| DIN 7985 / ISO 7045 | Pan Phillips screws | M1.6 – M10 | Machine screws |
| DIN 965 / ISO 7046 | CSK Phillips screws | M2 – M10 | Machine screws |
| DIN 963 / ISO 2009 | Slotted countersunk screws | M1.6 – M10 | Machine screws |
| DIN 84 | Slotted cheese head screws | M2 – M10 | Machine screws |
| DIN 85 | Slotted pan head screws | M3 – M10 | Machine screws |
| BS 450 | Slotted CSK and cheese head screws | 1/8" – 1/2" | Machine screws |
| DIN 7981 / ISO 7049 | Phillips pan head tapping screws | ST2.2 – ST6.3 | Self-tapping screws |
| DIN 7982 / ISO 7050 | Phillips CSK tapping screws | ST2.2 – ST6.3 | Self-tapping screws |
| DIN 7971 / ISO 1481 | Slotted pan head tapping screws | ST2.2 – ST6.3 | Self-tapping screws |
| DIN 7972 / ISO 1482 | Slotted CSK tapping screws | ST2.2 – ST6.3 | Self-tapping screws |
| DIN 125A | Plain washers | On request | Washers |
| DIN 127 / IS 3063 | Spring washers, flat section | On request | Washers |
| IS 6735 | Spring washers, square section | On request | Washers |
| DIN 6797 / 6798 | Toothed and serrated lock washers | On request | Washers |
| DIN 434 / 435 | Square taper washers for channels and I-sections | M8 – M27 | Washers |
| Studs | Standard and full-thread studs | On request | Studs & specials |
| Special bolts | Carriage bolts, U-bolts, setscrews | On request | Studs & specials |
| Other | Anchors, rivets, cup washers and nails | On request | Studs & specials |
| To drawing | Selected custom fasteners | On request | Studs & specials |
No standard matches that search. Ask us about it.
Size finder
Pick a size. See the numbers.
Thread pitch, spanner size, head and nut heights, Allen key and washer dimensions for ISO metric coarse fasteners.
- Pitch
- mm, coarse
- Spanner (ISO)
- mm across flats
- Spanner (DIN)
- mm across flats
- Bolt head height
- mm, ISO 4017
- Nut height
- mm, ISO 4032
- Allen key
- mm, ISO 4762
- Plain washer
- d1 × d2 × s, DIN 125A
- Spring washer
- d2 × s, DIN 127B
Materials & property classes
Strength and grade, side by side
Mechanical properties per ISO 3506 (stainless) and ISO 898-1 (carbon steel). Physical properties are typical values for the grade.
- A2-50 / A4-50500 / 210 MPa
- A2-70 / A4-70700 / 450 MPa
- A2-80 / A4-80800 / 600 MPa
- 4.6400 / 240 MPa
- 8.8800 / 640 MPa
- 10.91040 / 940 MPa
- 12.91220 / 1100 MPa
| Class | Material | Min. tensile (MPa) | Min. 0.2 % yield (MPa) | Elongation |
|---|---|---|---|---|
| A2-50 / A4-50 | Stainless, soft | 500 | 210 | 0.6 d |
| A2-70 / A4-70 | Stainless, cold-worked | 700 | 450 | 0.4 d |
| A2-80 / A4-80 | Stainless, high strength | 800 | 600 | 0.3 d |
| 4.6 | Mild steel (MS) | 400 | 240 | 22 % |
| 8.8 | High tensile (HT), ≤ M16 | 800 | 640 | 12 % |
| 10.9 | High tensile (HT) | 1040 | 940 | 9 % |
| 12.9 | High tensile (HT) | 1220 | 1100 | 8 % |
| Grade | Designation | Magnetic | Density | Max service temp. | Best for |
|---|---|---|---|---|---|
| SS 202 | Cr-Mn austenitic | Slightly | 7.80 g/cm³ | ≈ 800 °C | Indoor and dry conditions; lowest cost stainless |
| SS 304 (A2) | EN 1.4301 | No (annealed) | 8.00 g/cm³ | ≈ 870 °C | General-purpose; most common stainless fastener |
| SS 316 / 316L (A4) | EN 1.4401 / 1.4404 | No (annealed) | 8.00 g/cm³ | ≈ 870 °C | Marine, chemical and food environments |
| SS 310 | EN 1.4845 | No | 7.90 g/cm³ | ≈ 1100 °C | High-temperature service, furnaces and ovens |
| SS 410 | EN 1.4006 (martensitic) | Yes | 7.75 g/cm³ | ≈ 650 °C | Hardenable; used for tapping screws and wear parts |
| Brass | CuZn37 / CuZn39Pb3 | No | 8.4 – 8.5 g/cm³ | ≈ 200 °C | Electrical and decorative use |
| Copper | Cu-ETP | No | 8.94 g/cm³ | ≈ 200 °C | Electrical conductivity |
| Titanium Gr 2 | ASTM B348 | No | 4.51 g/cm³ | ≈ 300 °C | Light weight, excellent corrosion resistance |
Elongation for stainless classes is given as a multiple of the nominal diameter d, as in ISO 3506. Values for 8.8 apply up to M16.
Fastener basics
What the markings mean
Reading A2-70
The letter gives the steel group (A for austenitic), the digit the grade, and the number is one-tenth of the minimum tensile strength. A2-70 means austenitic steel, minimum 700 MPa.
Cold-headed vs machined
A cold-headed bolt keeps unbroken grain flow through the head. Machining from bar cuts across that grain, which can create planes of weakness.
Rolled vs cut threads
Thread rolling removes no metal and leaves the thread roots in compression, which improves fatigue strength compared with cut threads.
Magnetism
Austenitic stainless fasteners are normally non-magnetic. Cold working can leave some slight magnetism, which is normal.
Quick quote
Need fasteners? Get a quote.
Tell us the type, standard, size, length, grade and quantity. We confirm manufacturing lead time and price.
- Reply with a quotation for prototypes or batches
- Reference number by email as soon as you send
- Or call Daksh Shah on +91 90823 86814
Quote checklist
Tap what you already have
- Cut3 kW fibre laser
- Bend100 t, 3200 mm
- WeldLaser · TIG · arc
- FinishGrind · polish
Have a drawing ready? Send it for a quote.
Share the drawing, material, quantity, finish and delivery date. We review it and reply with a quotation for prototypes or repeat batches.