
Fasteners · 02 of 07
Stainless steel nuts
Hexagon, jam, nylock, domed cap, wing, square, flange and eye nuts, matched to the bolt grade, from M3 to M48.
- Laser cutting
- CNC bending
- Welding
- Finishing
Identify your fastener










Overview
Nuts: what and where
Nuts are matched to the bolt grade. Nylock nuts resist vibration, thin jam nuts lock a second nut, and cap nuts cover exposed thread ends.
- Standards
- 10
- Size range
- M3 – M48
- Usual grades
- SS 304 / SS 316
Used in
- Panel assembly
- Vibrating machinery
- Food & pharma equipment
- Furniture
- Access covers
- Lifting points
Types
10 types, one family
Hexagon, lock, nylock, cap, wing, square, flange and eye nuts. Each type below is manufactured to the standard shown, in the grades listed further down.
- 01
DIN 934 / ISO 4032
Hexagon nut
The standard nut for bolts and studs; height close to 0.8 d.
Used forGeneral assembly with hex bolts
- 02
BS 1083
Hexagon nut, inch
Imperial hex nut for BSW and UNC threads.
Used forOlder and imported machinery
- 03
DIN 439
Thin / jam / lock nut
About half the height of a standard nut; locks a second nut.
Used forAdjusters, locking a full nut
- 04
DIN 982 / ISO 7040
Nylock nut
Nylon insert grips the thread and resists loosening under vibration.
Used forMotors, fans, vibrating machines
- 05
DIN 985
Nylock nut, thin
Lower profile nylock where space is short.
Used forCovers, guards, compact assemblies
- 06
DIN 1587
Domed cap nut
Closed dome covers the thread end for a neat, safe finish.
Used forExposed furniture and equipment ends
- 07
DIN 315
Wing nut
Tightened by hand, no tool needed.
Used forAccess covers, frequently opened clamps
- 08
DIN 557
Square nut
Square body sits in a slot and does not turn.
Used forChannel slots, timber
- 09
DIN 6923
Hex flange nut
Integral flange spreads the load on thin sheet.
Used forSheet metal panels
- 10
DIN 582
Lifting eye nut
Forged eye that fits onto a stud for lifting.
Used forLifting points on studs
Technical data
Standards, sizes and dimensions
| Standard | Description | Size range |
|---|---|---|
| DIN 934 / ISO 4032 | Hexagon nuts | On request |
| BS 1083 | Hexagon nuts | 1/4" – 1.3/4" |
| DIN 439 | Thin / jam / lock nuts | M3 – M48 |
| DIN 982 / ISO 7040 | Nylock nuts | M5 – M24 |
| DIN 985 | Nylock nuts, thin type | M3 – M20 |
| DIN 1587 | Domed cap nuts | M4 – M24 |
| DIN 315 | Wing nuts | M3 – M20 |
| DIN 557 | Square nuts | M5 – M16 |
| DIN 6923 | Hexagon flange nuts | M5 – M20 |
| DIN 582 | Lifting eye nuts | M6 – M36 |
| Size | Pitch (mm) | Across flats ISO (mm) | Across flats DIN (mm) | Nut height m, ISO 4032 (mm) |
|---|---|---|---|---|
| M3 | 0.5 | 5.5 | 5.5 | 2.4 |
| M4 | 0.7 | 7 | 7 | 3.2 |
| M5 | 0.8 | 8 | 8 | 4.7 |
| M6 | 1.0 | 10 | 10 | 5.2 |
| M8 | 1.25 | 13 | 13 | 6.8 |
| M10 | 1.5 | 16 | 17 | 8.4 |
| M12 | 1.75 | 18 | 19 | 10.8 |
| M14 | 2.0 | 21 | 22 | 12.8 |
| M16 | 2.0 | 24 | 24 | 14.8 |
| M20 | 2.5 | 30 | 30 | 18.0 |
| M24 | 3.0 | 36 | 36 | 21.5 |
| M30 | 3.5 | 46 | 46 | 25.6 |
| M36 | 4.0 | 55 | 55 | 31.0 |
Nominal values from the standard. Lengths follow the standard series; non-standard lengths on request.
| Thread | ISO metric coarse |
|---|---|
| Types | Hex, jam, nylock, cap, wing, square, flange, eye |
| Property class | A2-70 / A4-70 (match the bolt) |
| Finish | Plain stainless |
| Stainless steel grades | 202 · 304 · 310 · 316 · 316L · 410 |
| Other materials | HT · MS · Copper · Brass · Titanium |
Usually manufactured in:
- SS 304 (A2)
- SS 316 / 316L (A4)
- SS 202
| Grade | Designation | Magnetic | Density | Max service temp. | Best for |
|---|---|---|---|---|---|
| SS 202 | Cr-Mn austenitic | Slightly | 7.80 g/cm³ | ≈ 800 °C | Indoor and dry conditions; lowest cost stainless |
| SS 304 (A2) | EN 1.4301 | No (annealed) | 8.00 g/cm³ | ≈ 870 °C | General-purpose; most common stainless fastener |
| SS 316 / 316L (A4) | EN 1.4401 / 1.4404 | No (annealed) | 8.00 g/cm³ | ≈ 870 °C | Marine, chemical and food environments |
Choosing
Picking the right one
Quick guidance from the standards. For critical joints, follow your design calculation.
Which grade of nut?
Match the nut to the bolt: an A2-70 bolt takes an A2-70 nut, an A4 bolt an A4 nut. Mixing 304 and 316 in a wet joint is best avoided.
Nylock or spring washer?
For vibration, a nylock nut keeps a prevailing torque even if preload drops. Nylon inserts are generally limited to about 120 °C; use an all-metal lock nut above that.
How much thread through the nut?
At least one full thread should project beyond the nut after tightening.
Size finder
Pick a size. See the numbers.
Thread pitch, spanner size, head and nut heights, Allen key and washer dimensions for ISO metric coarse fasteners.
- Pitch
- mm, coarse
- Spanner (ISO)
- mm across flats
- Spanner (DIN)
- mm across flats
- Bolt head height
- mm, ISO 4017
- Nut height
- mm, ISO 4032
- Allen key
- mm, ISO 4762
- Plain washer
- d1 × d2 × s, DIN 125A
- Spring washer
- d2 × s, DIN 127B
Quick quote
Quote for nuts
Tell us the standard, size, length, grade and quantity. We confirm manufacturing lead time and price.
- Reply with a quotation for prototypes or batches
- Reference number by email as soon as you send
- Or call Daksh Shah on +91 90823 86814
Quote checklist
Tap what you already have
- Cut3 kW fibre laser
- Bend100 t, 3200 mm
- WeldLaser · TIG · arc
- FinishGrind · polish
Have a drawing ready? Send it for a quote.
Share the drawing, material, quantity, finish and delivery date. We review it and reply with a quotation for prototypes or repeat batches.